單片機畢業設計外文翻譯---基于 at89s51 單片機的微型土壤濕度檢測儀設計

1、<p><b>　　畢 業 設 計</b></p><p><b>　?。ㄍ馕姆g材料）</b></p><p>　　2011年 6 月 </p><p>　　The design Based on AT89S51 miniature soil humidity detector design</p

2、><p>　　Abstract: facilitate master soil moisture conditions, design the miniature soil humidity detector. Its hardware system includes signal amplifier circuit, A/D circuit, SCM, micro LCD display and alarm cir

3、cuit, etc.; Software system includes A/D conversion driver, LCD driver two modules. Proteus software platform based on the design of the system is simulated, and the results show that the system hardware and software des

4、ign correct and reliable operation.</p><p>　　Keywords: soil humidity; Detector; SCM; A/D conversion; simulation</p><p>　　TP202 classification number: Chinese</p><p>　　Literature ide

5、ntification code: A</p><p>　　Section 1 Introduction</p><p>　　Agricultural production in the economic development of our country has important position, for farmers Industry production to provi

6、de timely and reliablly technical service has become the heavily meteorological department To response one. Along with the national governments at all levels of agricultural production increasingly heavier</p><

7、;p>　　Depende on the service, my unit also serve for agriculture, promote for increasing farmers' income</p><p>　　Many studies, the various problems in agricultural production also widely adjustable<

8、;/p><p>　　Inquiry. Research found that gardening cultivation, greenhouse flowers, awning vegetables one</p><p>　　Some valuable varieties of soil moisture, soil has a high requirement, humidity</

9、p><p>　　At the time, not only seriously affecting its normal growth, and even cause planting product death Wu, causing serious damage. Farmers Therefore, engaged in this kind of agricultural production.Farmers

10、very need a low cost, small volume and detection reliable soil .Soil humidity detector for water supply, provides the basis. In order to solve the above asked .Our problem, I unit combined with actual conditions of agric

11、ultural production, and the related units designed</p><p>　　Home of high precision, to design the low cost of miniature soil moisture detection instrument.</p><p>　　Along with the social life pr

12、ogress, people's quality of life is getting much more better, flowers has become a fashion. Flowers can not only enrich people's cultural life and is good for mental and bodily health ，but also can improve and pu

13、rify air, improve health. Water is necessary for flower’s growth ,it influences the growth of flowers greatly. Too much water or too little, will affect the normal growth and the kind of flower is verious, Different f

14、lowers need different amount of water. </p><p>　　Section 2 composition of the system </p><p>　　The whole system consists of SCM, circuit of DAQ, keyboard input and digital display circuit, outpu

15、t controlling circuit etc. circuit of CAQ is made of 4 SRH and adc , SRH makes flower’s soil humidity convert into analog voltage output, adc makes the output of analog voltage convert into digital quantity and send to m

16、icrocontroller. AT89S52 is adopted, the collectted value of soil humidity is compared with a preset limit soil moisture, and it makes corresponding judgement according to the compar</p><p>　　Miniature soil d

17、etector signal processing system including soil humidity sensor</p><p>　　Device, A/D acquisition circuit, SCM and micro LCD. Its work After cheng is: soil soil wet degrees preach sensor, will wet degrees let

18、ter sent to A/D adopt set electricity</p><p>　　Road, the A/D conversion, income data digital signal into SCM Processing, finally will processing results sent to micro LCD display.</p><p>　　Secti

19、on 3 the hardware design of system </p><p>　　3.1 the circuit’s working principle </p><p>　　The hard thing the original reason system graph as figure 2 shows. This article selects KSC -6V integra

20、ted relative humidity sensor, wait for after inserting the soil about 5s make sensor</p><p>　　Implement fully contact with the soil, signal by integrated amp LM324 Vin the same phase</p><p>　　In

21、put terminal. The sensor's relative humidity 0% ~ 100% RH, its corresponding</p><p>　　Output is 0 ~ 100mV [1]. According to the integrated amp with phase ratio amplification gain: Kf=R1+ Rf =1+ 47 =48<

22、;/p><p>　　Then the output amplification V0 = 48 analog signal voltage, so output analog, Vi, electric pressure fan letter surrounded is 0 ~ 4.8v. This mode, turn into A/D CH0 slice of replace core general way

23、into line changeover place, have cut to several words AT89S51 single-chip letter Numbers again into data processing and the LCD.</p><p>　　3.2 A/D conversion chip choice and controlling principle</p>&

24、lt;p>　　This article chooses A/D conversion chips for ADC0832, this chip is 8</p><p>　　Pin double row straight insert dual channel A/D converter, can separately for both road simulation No real now believe

25、 d/a change, can use in the ocl lose into mode and bad points to lose</p><p>　　Under the way of DI server channel selected choose, several according to adopt sets and Data transfer [2].</p><p>　

26、　The work of ADC0832 do sequence as shown in figure 3. Root according to our web site, when covariance .ADC0832 did not work, must the piece selected in the high level, the CS</p><p>　　When chip disabled. Wh

27、en should undertake A/D conversion shall be piece selected end CS offsets</p><p>　　In low level and maintains to convert over. Chip began to work, still need to make</p><p>　　Monolithic machine

28、to core chips, when the clock CLK lose faith in the clock pulse blunt when lose,</p><p>　　In the first clock pulse before the sinking DI end must be high electric flat, tables</p><p>　　And start

29、 signal. In the first 2, 3 pulse sinking DI end before should be lost</p><p>　　Into two data used to select channels function. Channels are as follows:</p><p>　　(1) the controlled conditions<

30、/p><p>　　In accordance with The Times when DI lost with 1, 0, the only way to do CH0 tong general turned into single wordChange; </p><p>　　(2) when DI ordinal input 1, 1, only for single CH1 channe

31、l onTao transformation;</p><p>　　(3) when DI ordinal 0, 0, will CH0 as is, will CH0 input 0 as its negative input IN CH1 -, as are the input IN +</p><p>　　3.3 microcontroller’s choice</p>

32、<p>　　MCU is the control of core, compared with the others ,we chose AT89S51 single-chip microcomputer. The advantages of this type of single-chip microcomputer is [3] : </p><p>　　(1) The single-chip

33、microcomputer and the 8051 series microcontroller is fully compatible, make it use easily, and into the ten points Cheap; </p><p>　　(2) Internal memory can be repeated CaXie by the EEPRROM, be helpful for re

34、peatting modify the program;</p><p>　　(3) has the low consumption working methods and to be achieved Off electrical automatic protection; </p><p>　　(4) has strong anti-jamming, greatly improving

35、 the worthRoyal external electromagnetic interference ability, so it is especially suitable for relatively tough in conditions Under the poor conditions of the job.</p><p>　　3.4 The use of LCD</p>&l

36、t;p>　　Using micro LCD display device, 1602LCD, its performance point is: working voltage only 4.5 ~ 5.5 V; Very low power consumption (work current</p><p>　　Only 2.0 mA); And reliable work; Small volume (

37、can show 16 x 2 words</p><p>　　Operators). Its characters are displayed by internal special displacement function of HD44780 dynamic core slice [4]</p><p>　　Quasi ASCII put into their number wit

38、hin department set into reservoir with deposit according to show and editor (DDRAM), inside the ministry accused of line of road will move will word from sheba operators preach send to show, Implement. Monolithic machin

39、e and the number of 1602LCD between general P0 into change had to enter line, resistance for P0 mouth R9 R2 ~ the pull-up resistors</p><p>　　Section 4 The software design of the control of system</p>

40、<p>　　This recorder controlling software design adopts modular thought.</p><p>　　According to the function,w emake the controlling system software devide into two big modules: </p><p>　　(1

41、) ADC0832 driver module, to control the collection of voltage signal;</p><p>　　(2) 1602LCD driver module, show soil humidity. This system driver using C</p><p>　　Language design, its main progra

42、m is as follows</p><p>　　Main (void)</p><p><b>　　{</b></p><p>　　unsigned int AD_val;</p><p>　　Convert the value after the</p><p>　　unsigned int

43、 Int, Dec;</p><p>　　The converted the integer part and the decimal part</p><p>　　/ / storage save A/D</p><p>　　/ / points don't store in existence</p><p><b>　

44、　change</b></p><p>　　LcdInitiate ();</p><p>　　/ / to be liquid crystal early beginning</p><p><b>　　}</b></p><p>　　2)the production of clock</p>

45、<p>　　When the clock points frequency device (after it can have to 4.5 MHz in turn when the change in A/D clock) turn change when idle is empty, the hold after A state in ADCR is written to the START field immediat

46、ely START 01 (conversion) or the selected edge appear in choice of signal sampling clock can immediately START. This feature can save power consumption. ADC conversion clock computation formula is as follows</p>&

47、lt;p>　　FADC=FPCK/（CLKDIV+1）</p><p>　　Type: Fpclk - core slice; when the clock set After CLKDIV - points of ADC conversion clock frequency.</p><p>　　3) interrupted.</p><p>　　When

48、DONE bits is 1, A/D conversion module to vector interrupt controller (VIC) issued an interrupt request in the VICIntEnable VIC, if Bit8 (A/D conversion interrupts enabled bits) make can, then can produce the interruption

49、. Read ADDR will reset DONE bits. This paper mainly A/D acquisition C language driver section design is as follows:</p><p>　　/***********************************</p><p>　　Function: A/D acquisiti

50、on</p><p>　　Entrance parameters: CH_i</p><p>　　/***********************************</p><p>　　void AD_Change(unsigned char CH_i)</p><p><b>　　{</b></p>

51、<p>　　ADC0R = (1 < < CH_i) | / / choose channels I carry A/D acquisition ((Fpclk / 1,000, 000-1) < < 8 | / / set convert clock</p><p>　　(0 < < 16)</p><p>　　(0 < < 1

52、9)</p><p>　　| / / BURST = 0, software control conversion operations</p><p>　　| / / normal A/D acquisition modes</p><p>　　(0 < < 27);| / / decrease along the startup conversion

53、</p><p>　　AD0DR; DO = / / read take ADC and fruit, and clear except</p><p>　　DONE mark bits</p><p><b>　　while (1)</b></p><p><b>　　.</b></p>

54、;<p><b>　　.</b></p><p><b>　　}</b></p><p>　　Section5 temperature measuring system of Proteus software simulation</p><p>　　To ensure system on the hardw

55、are and software system, reliable work the Proteus software simulation. The basic process is first draw HaoTu 3 illustrates the simulation</p><p>　　Electricity by road after Keil soft thing, Ed into the tran

56、slation and born of dynamic soft thing ec flooding (files) : LPC2131 loaded. And Proteus software environment</p><p>　　The simulation results (" + 3V corresponding full amount 30Kpa) the process design

57、of the software and hardware the results show that the system is correct</p><p>　　To ensure that the design of the software and hardware of soil detector is correct this paper designs proteus soft thing into

58、 line imitation true. The base this process is first draw had made good figure 2 shows simulation circuit, Keil software compiled by again and to create system driver (" *. Wen pieces ") load: the monolithic ma

59、chine, and will figure 2 virtual dc voltage signal generator set to 45mV. Then the simulation of voltage: enlarge V0 = 48 x 0.045 = 2.16 V, soil relative humidity sh</p><p>　　The simulation results show that

60、 the 45.18% RH "(for" the calculation and existing tiny</p><p>　　According to convert error). The results show that the system software and hardware design are right.</p><p>　　Section6

61、 conclusion</p><p>　　This paper introduces some machine oxygen pressure detection adjustment system design of the software and hardware square method. This set with set in A project into A/D turn changing m

62、ould pieces of high sexual can LPC2131 chip, tell the plus special A/D acquisition chip, simplified the peripheral circuit design. The system design is simple in structure, reliable in trial has obtained good effect.<

63、/p><p>　　(1) this design using highly integrated humidity detector A/D conversion chip, SCM and LCD module, greatly simplifying the hardware circuit and significantly reduce the size and cost of A circuit board

64、.</p><p>　　(2) electric pressure letter in ADC0832, integrating core piece of work is really is. Ec</p><p>　　The most important premise, to ensure reliable of the analog signal collection, colle

65、ction need before use integrated amp sensor signal amplifier.</p><p>　　(3) the loam soil by small, measuring devices body product by pure degree is high and measured this very low, suitable to use of agricul

66、tural first production line.</p><p>　　(4) the system can shorten Proteus simulation designing cycle, managing hardware investment. The simulation results show that the system design is correct, reliable oper

67、ation</p><p>　　Section 7 References</p><p>　　[1] 孫余凱,吳鳴山,項綺明.集成運算放大器實用電路識圖[M].北京</p><p>　　[2] 李贛平,邵惠鶴.基于 ARM 的高精度智能流量變送器的設計[J]</p><p>　　[3] 馮偉,白瑞林,李祥偉.基于 WinCE5.0 的數字式觸

68、摸屏驅動程序的開發[J].自動化儀表, 2009,9.</p><p>　　[4] 張洪潤. 傳感器應用設計 300 例（上冊）[M].北京: 北京航空航天大學出版社, 2006.</p><p>　　[5] 徐瑋. C51 單片機高效入門[M]. 北京: 機械工業出版社, 2007.</p><p>　　[6] 師寶山.基于 AT89S51 的多參數氣體檢測儀的研

69、制[J].微計算機信息, 2007, 7~1.</p><p>　　[7] 周堅.單片機輕松入門[M].北京:北京航空航天大學出版社, 2004.</p><p>　　基于 AT89S51 單片機的微型土壤濕度檢測儀設計</p><p>　　摘要： 為便于掌握土壤的濕度狀況， 設計了微型土壤濕度檢測儀。 其硬件系統包括信號放大電路、 A/D 轉換電路、 單片機、 微

70、型液晶顯示器和報警電路等； 軟件系統包括 A/D 轉換的驅動程序 、 液晶驅動</p><p>　　程序兩個模塊。 基于 Proteus 軟件平臺對系統的設計進行了仿真， 結果表明系統的軟硬件設計正確，運行可靠。</p><p>　　關鍵詞： 土壤濕度； 檢測儀； 單片機； A/D 轉換； 仿真</p><p>　　中圖分類號： TP202</p>&

71、lt;p><b>　　文獻標識碼： A</b></p><p><b>　　第一章引言</b></p><p>　　農業生產在我國的經濟發展中具有重要地位，為農業生產提供及時、 可靠的技術服務已成為氣象部門的重要職責之一 。 隨著國家各級政府對農業生產的日益重視，我單位也在服務農業、 促進農民增收等方面開展了許多研究 ，對農業生產中的各項問

72、題也進行了廣泛調研.調研發現， 園藝栽培、溫室花卉、大棚蔬菜等的某些名貴品種，對土壤濕度有著極高的要求，土壤濕度不當時，不僅嚴重影響其正常生長，甚至?xí)?dǎo)致種植品死亡，造成農民的嚴重損失。為此，從事該類農業生產的農民朋友非常需要一種成本低、體積小且檢測可靠的土壤濕度檢測儀，為水分供應提供依據。為了解決以上問題，我單位結合我區農業生產實際狀況，和有關單位專家共同設計了高精度 、低成本的微型土壤濕度檢測儀 。</p><p

73、>　　本文則詳細介紹了該檢測儀的測控電路和相關軟件流程。</p><p><b>　　第二章系統的組成</b></p><p>　　微型土壤檢測儀的信號處理系統包括土壤濕度傳感器、A/D 采集電路、單片機和微型液晶顯示器。其工作過 程 是 ：土 壤 濕 度 傳 感 器 將 濕 度 信 號 送 至 A/D 采 集 電路，經 A/D 轉換后，所得數字信號送入單片機進

74、行數據處理，最后將處理結果發送到微型液晶顯示器顯示。</p><p>　　第三章 系統的硬件設計</p><p>　　3.1 電路的工作原理</p><p>　　本文所選的KSC-6V集成相對濕度傳感器插入土壤后，等待約5s使傳感器充分接觸土壤后，信號 Vin 經集成運放 LM324 的同相輸入端。該傳感器的相對濕度 0%~100%RH 時，其對應的輸出為 0~10

75、0mV[1]。根據集成運放的同相比例放大增益：Kf=R1+ Rf =1+ 47 =48</p><p>　　則放大后的輸出模擬信號電壓V0=48?Vi，故輸出模擬信號電壓范圍為 0~4.8V。該模擬信號進入A/D 轉換芯片的CH0 通道進行轉換處理，所 得到數字信號再送入單片機 AT89S51 進行數據處理并由液晶顯示。</p><p>　　3.2 A/D 轉換芯片的選擇與控制原理<

76、/p><p>　　本文選擇的 A/D 轉換芯片為 ADC0832，該芯片為8引腳雙列直插式雙通道 A/D 轉換器，能分別對兩路模擬信號實現 模/數 轉換，可以用在單端輸入 方式和差分輸入方式下工作，其中DI端進行通道選 擇、數據采集和數據傳送[2]。ADC0832的工作。根據協議，當ADC0832 未工作時，必須將片選端 CS 置于高電平，此時芯片禁用。當要進行A/D 轉換時，應將片選端CS置于低電平并保持到轉換結束

77、。芯片開始工作后，還需讓單片機向芯片的時鐘信 號輸入端 CLK 輸入時鐘脈沖，在第一個時鐘脈沖的下沉之前 DI 端必須是 高電平，表示起始信號。在第2、3個脈沖的下沉之前DI 端則應輸入兩位數據用于選擇通道功能。通道受控情況如下： </p><p>　　①當DI依次輸入1、0 時，只對CH0通道進行單通道轉換；</p><p>　?、诋?dāng)DI依次輸入1、1 時，只對CH1通道進行單通道轉換；

78、</p><p>　?、郛?dāng)DI依次輸入0、0 時，將CH0作為正輸入端 “IN+”，CH1作為負輸入端“IN-”；</p><p>　?、墚?dāng)DI依次輸入 0、1 時，將CH0作為負輸入端“IN-”，CH1作為正輸入端“IN+”。</p><p>　　在第 3 個脈沖下沉之后，DI 端的輸入電平就失去輸入作用 ，此 后數據 輸出端DO開始輸出轉換后的數據 。</

79、p><p>　　在第4個脈沖的下降沿輸出轉換后數據的最高位，直到第11個脈沖下降沿輸出數據的最低位，至此 ，一個字節的數據輸出完成。正常情況下，ADC0832 與單片機的接口應為4條數據線，分別是CS、CLK、DO、DI。但由于 DO 和 DI兩個端口在通信時并未同時使用，而是先由DI端口輸入兩位數據（0 或 1）來選擇通道控制，再由DO端輸出數據 。因此，在I/O 口資源緊張時，可以將 DO 和并聯在一根數據線上使

80、用。</p><p>　　3.3 單片機的選擇</p><p>　　單片機是控制記錄儀工作的核心，經過比較采用AT89S51 型單片機。該型單片機的優點是[3]：</p><p>　?、僭搯纹瑱C與 8051 系列單片機完全兼 容 ，容易使用，且成本十分低廉；</p><p>　?、趦?nèi)部存儲器采用可反復擦寫的 EEPRROM，有利于反復修改程序

81、；</p><p>　?、劬哂械秃哪芄ぷ鞣绞胶湍軌?qū)崿F(xiàn)掉電自動保護； </p><p>　?、芫哂休^強的抗干擾性，大大提高了抵御外界的電磁干擾能力，所以特別適合在條件相對惡劣的條件下工作。</p><p>　　3.4 液晶顯示器的使用</p><p>　　顯示器件采用微型液晶顯示器 1602LCD，其性能特點是：工作電壓僅需 4.5～5.5V

82、；功耗非常低（工作電流只有 2.0mA）；且工作可靠；體積?。娠@示 16×2 個字符）。其字符顯示功能由內部專用的驅動芯片HD44780[4]準ASCII碼放入其內部集成的數據顯示用存儲器（DDRAM），內部控制線 路就會自動將符傳送到顯示器上 。單片機和1602LCD之間的數據交換通過P0 進行，電阻R2～R9為P0口的上拉電阻。</p><p>　　第四章 系統的控制軟件設計</p>

83、<p>　　本記錄儀的控制軟件設計采用模塊化思想</p><p>　　根據功能將系統控制軟件分為兩大模塊： </p><p>　?、貯DC0832的驅動程序模塊，控制電壓信號的采集；②1602LCD 的驅動程序</p><p>　　模塊，顯示土壤濕度。本系統的驅動程序采用 C 語言設計，其主程序如：</p><p>　　main

84、(void)</p><p><b>　　{</b></p><p>　　unsigned int AD_val;轉換后的值</p><p>　　unsigned int Int,Dec;</p><p>　　轉換后的整數部分與小數部分</p><p><b>　　//儲 存 A/D&l

85、t;/b></p><p><b>　　//分 別 儲 存</b></p><p>　　LcdInitiate () ;</p><p>　?。?） 時 鐘 產 生 。時鐘分頻器（ 通過它可以得到4.5MHz 的轉換時鐘 ）在A/D 轉換器空閑時保持復位狀態，在 ADCR 的START字段被寫入01（立即啟動轉換）或所選邊沿出現在選擇的信

86、號上時可立刻啟動采樣時鐘。</p><p>　　這個特性可以節省功耗。ADC 轉換時鐘的計算公式如下：</p><p><b>　　FADC=</b></p><p><b>　　CLKDIV+1</b></p><p>　　式 中 ：Fpclk—芯片外設時鐘；CLKDIV—分頻后的ADC轉換時鐘。

87、</p><p>　?。?）中斷。當DONE位為1時，A/D轉換模塊向向量中斷控制器（VIC）發出中斷請求，如果VIC中VICIn-tEnable的Bit8（A/D 轉換中斷使能位）使能， 則會產生中斷。讀取 ADDR 將清零 DONE 位。</p><p>　　本文主要的 A/D 采集 C 語言驅動程序段設計如下：</p><p>　　/*************

88、**********************</p><p>　　函數功能：A/D 采集</p><p><b>　　入口參數：CH_i</b></p><p>　　************************************/</p><p>　　void AD_Change(unsigned char C

89、H_i)</p><p><b>　　{</b></p><p>　　ADC0R=(1<<CH_i) | //選擇通道 i 進行 A/D 采集</p><p>　　((Fpclk/1000000-1)<<8 | //設置轉換時鐘</p><p><b>　?。?<<16）&

90、lt;/b></p><p><b>　?。?<<19）</b></p><p>　　| //BURST=0，軟件控制轉換操作</p><p>　　| //正常 A/D 采集模式</p><p>　　0<<27）; | //下降沿啟動轉換</p><p>　　

91、DO =AD0DR; //讀 取 ADC 結 果 ， 并 清 除</p><p><b>　　DONE 標志位</b></p><p>　　第五章 測溫系統的 Proteus 軟件仿真</p><p>　　為確保系統的可靠工作， 對軟硬件系統進行了 Proteus 軟件仿真。 其基本過程是先繪制好圖 3 所示的仿真電 路 后 ， 將

92、由 Keil 軟 件 編 譯 并 生 成 的 系 統 驅 動 軟 件（hex 文件）載入 LPC2131。 并在 Proteus 軟件環境中， 在Vin 端口輸入電壓 “V=+3V”， 啟動仿真 </p><p>　　為確保土壤檢測儀的軟硬件設計正確，本文對設計進行了 Proteus 軟 件 仿真。所示的仿真電路，再將由 Keil 軟件編譯并生成的系統驅動 程序 （“*.hex 文 件 ”） 載 入 單 片 機

93、，并 將圖 2 中 的 虛擬直流電壓信號發生器設為 45mV。 則其放大后的模擬電壓： V0=48×0.045=2.16V， 土壤的相對濕度應為： RH=2.16 ×100=45%RH。 啟動仿真即可看到圖 2 中 1602LCD4.8上的仿真結果顯示為“45.18%RH”（存在微小的計算和數據轉換誤差） 該結果表明，系統的軟、硬件設計正確。</p><p><b>　　第六章 結論

94、</b></p><p>　　本文介紹了某機氧氣調節系統壓力檢測的軟硬件設計方法 。該設計采用集 成有A/D轉換模塊的高性能LPC2131 芯片，省去了外加專用 A/D 采集芯片， 簡化了外圍電路設計。系統整體設計結構簡單，運行可靠，在試用中取得了良好效果。</p><p><b>　　第七章 參考文獻</b></p><p>　　

95、[1]孫余凱,吳鳴山,項綺明.集成運算放大器實用電路識圖[M].北京:電子工業出版社,2008.</p><p>　　[2]李贛平,邵惠鶴.基于ARM 的高精度智能流量變送器的設計[J].電子技術應用,2008,12.</p><p>　　[3] 馮偉,白瑞林,李祥偉.基于 WinCE5.0 的數字式觸摸屏驅動程序的開發[J].自動化儀表, 2009,9.</p><p

96、>　　[4] 張洪潤. 傳感器應用設計 300 例（上冊）[M].北京: 北京航空航天</p><p>　　大學出版社, 2006.</p><p>　　[5] 徐瑋. C51 單片機高效入門[M]. 北京: 機械工業出版社, 2007.</p><p>　　[6] 師寶山.基于 AT89S51 的多參數氣體檢測儀的研制[J].微計算機</p>