swt計測儀器上應用 壓電流量計 計數器ch-en ok

1、SWT 壓電流量計 壓電流量計 flow meter流量計是按傳感器探頭插入管道并剛好接觸流體來進行設計的。傳感器探頭頂部承受流體切應力的大小正比于流體的流量。The design of flow meter is according to the sensor probe inserted into the pipe and just touching the fluid. Fluid shear stress on the top

2、of sensor probe is in direct proportion to the volume of fluid flow.如圖 3.28 所示，圖 3.29 是圖 3.28 中檢測探頭的放大圖。在這兩圖中 1 為管節部分，2 為金屬制的管節外殼，3 為管子襯套，4 為位置調節螺桿，5 為 T 型管節(即孔腔)，6 為法蘭盤，7 為孔腔襯套，8 為探頭，9 為探頭頂部，10 為探頭體，11 為底板，12 為襯墊，13 為接地

3、引線，14 為信號引線，15 為壓電陶瓷傳感器，16 為同軸電纜的中心線，17 為同軸電纜的接地屏蔽線，18 為絕緣子，19 為信號放大器，20及 21 為法蘭盤，22 為遙控指示電路，23 為電源電路。As shown in Fig.3.28, Fig.3.29 is detector probe’s magnification of Fig.3.28. In these two figures,1-the part of pipe

4、section, 2-the metal shell of pipe section, 3-the pipe bushing, 4-the adjusting screw of position, 5-the T type pipe section ( i.e. Hole cavity),6-the flange plate;7-the bushing of hole cavity;8-the probe,9-the top of pr

5、obe, 10-the probe body,11-the baseboard,12-the pads, 13-the GND wire, 14-the signal wire, 15-the piezoelectric ceramic sensor,16-the center line of coaxial cable, 17-The GND shielding wire of coaxial cable, 18-the insula

6、tor, 19-the signal amplifier, 20 and 21-the flange plate, 22-the remote indication circuit, 23- the power supply circuit.圖:3.28 流量計縱剖面圖和插入檢測裝置的電路方框圖.圖:3.29 放大的檢測探頭把 T 型管節用螺栓擰緊在被測流體管道的管接頭法蘭盤上,在 T 型管節中插入流量計探頭就可測量流體速度。Screw

7、 the T type pipe section down on the flange plate with detected fluid pipe connection and measure the fluid speed with a flow meter probe inserted in T type tube.壓電計數器由一雙膜片型壓電元件和圖 3.49 所示的檢測電路構成。 當物品 G 落到壓電陶瓷元件 5上時，由于壓

8、電陶瓷元件的壓電效應產生電信號，此電信號經可控硅整流器的柵極使可控硅導通，經電阻R1 加到晶體管 4 的基極上，導通集電極和發射極，啟動磁繼電器，使計數器工作。Piezoelectric counter consists of a double diaphragm type piezoelectric element and the detection circuit shown in Fig.3.49. When the item G

9、 falls down to the piezoelectric ceramic element 5, the electrical signal produced by piezoelectric effect of piezoelectric element will conduct SCR via grid electrode of SCR rectifier, which will conduct collector and e

10、mitter to start magnetic relay and make the counter work with R1 added to the base electrode of transistor.圖:3.29 壓電計數器線路圖當壓電陶瓷元件接受下一個物品再進行動作時，因為電源電流直接為最初的逆極性成分所截止，因而壓電陶瓷元件接受物品的反應次數能正確地由磁繼電器的開閉而進入計數器，并進行運算。這樣，這種簡單的裝置能夠正確

11、地、靈敏地對落到壓電陶瓷元件上的物品進行計數和記錄。When the piezoelectric ceramic element receives next item and acts again, and the supply current is directly cut off by the original composition of reverse polarity, the reaction times of piezoe

12、lectric ceramic element receiving items will correctly make the counter work and calculate via magnetic relay’s opening and closing. Thus, these simple devices can correctly and swiftly count and record items falling dow