版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領
文檔簡介
1、<p><b> 附 錄1</b></p><p> Differential and Rear Axles</p><p> The differential is part of the rear-axle-housing assembly, which includes the differential, rear axles, wheels,
2、and bearings. If the car were to be driven in a straight line without having to make turns, then no differential would be necessary. However, when the car rounds a turn, the outer wheel must travel farther than the inner
3、 wheel. The differential permits the two rear wheels to rotate different amounts when the car goes around a turn, while still delivering power to both rear wheels.</p><p> The rear axles are attached to the
4、 wheels and have bevel side gears on their inner ends. The differential case is assembled on the left axle but can rotate on a bearing independently of the axle.The differential case supports the differential-pinion gear
5、 on a shaft, and this gear meshes with the two bevel gears. The ring gear is attached to the differential case so that the case rotates with the ring gear when the later is driven by the drive pinion.The driving power en
6、ters the differential thro</p><p> Attached to the ring gear (through the differential case) is a differential-pinion shaft on which are assembled two differential-pinion gears. Each rear car wheel has a se
7、parate axle, and there are two side gears splined to the inner ends of the two wheel axles. The two differential-pinion gears mesh with these two side gears. When the car is on a straight road, the two differential-pinio
8、n gears do not rotate on the pinion shaft, but they do exert pressure on the two side gears so that the side </p><p> The differential case is supported in the carrier by two tapered-roller side bearings. T
9、his assembly can be adjusted from side to side to provide the proper backlash between the ring gear and pinion and the required side bearing preload. This adjustment is achieved by threaded bearing adjusters on some unit
10、s and the placement of selective shims and spacers on others.</p><p> Transaxle final drive gears provide the means for transmitting transmission output torque to the differential section of the transaxle.
11、The differential section of the transaxle has the same components as the differential gears in a RWD axle and basically operate in the same way. The power flow in transversely mounted power trains is in line with the whe
12、els and therefore the differential unit does not need to turn the power 90 degrees.</p><p> When the car rounds a curve, the outer wheel must turn faster than the inner wheel. To permit this, the two pinio
13、n gears rotate on their pinion shaft, transmitting more turning movement to the outer side gear than to the inner side gear. Thus, the side gear on the outer-wheel axle turns more rapidly than the side gear on the inner-
14、wheel axle. This permits the outer wheel to turn more rapidly while the car is rounding the curve.There are two basic types of axle: dead axles and live axle. The dead</p><p> Propeller Shaft and Universal
15、Joint</p><p> The propeller shaft is a drive shaft to carry the power from the transmission to the rear-wheel axles. It connects the transmission main, shaft carries through the propeller shaft to the diffe
16、rential at the rear axles. Rotary motion of the transmission main shaft carries through the propeller shaft to the differential, causing the rear wheels to rotate.</p><p> The propeller-shaft design must ta
17、ke two facts into consideration. First, the engine and transmission are more or less rigidly attached to the car frame. Second, the rear-axle housing (with wheels and differential) is attached to the frame by springs. As
18、 the rear wheels encounter irregularities in the road, the springs compress or expand. This changes the angle of drive and the distance between the transmission and the differential, and the propeller shaft may take care
19、 of these two changes. Tha</p><p> The propeller shaft may be solid or hollow, protected by an outer tube or exposed. Some applications include bearings at or near the propeller shaft center to support the
20、shaft. The two-section propeller is supported by a center bearing and coupled together by universal joints. A universal joint is essentially a double- hinged joint consisting of two Y-shaped yokes, one on the driving sha
21、ft and the other on the driven shaft, and across-shaped member called the spider. The four arms of the spider</p><p> A slip joint consists of outside splines on one shaft and matching internal splines in t
22、he mating hollow shaft, the splines cause the two shafts to rotate together but permit the two to move endwise with each other. This accommodates any effective change of length of the propeller shaft as the rear axles mo
23、ve toward or away from the car frame.</p><p><b> 差速器和后車軸</b></p><p> 差速器是后車軸體系的一部分,此體系包括差速器,后車軸,輪子和軸承。如果直線行車而不轉彎,則不需要差速器。然而,車轉彎時,外面輪子的速度必須比里面的輪子快。差速器保證車轉彎時外面輪子的旋轉比里面輪子快,同時給兩個后車輪提供動
24、力。</p><p> 后車軸和輪子相連,并且在內部的終端有傾斜齒輪。差速器在左車軸,但是能在車軸的軸承上獨立旋轉。差速器能使差速副齒輪作用于一個柄上,齒輪和兩個斜齒輪互相咬合。環行齒輪和差速裝置相連,從而使這個裝置在副齒輪旋轉時和環行齒輪一起旋轉。通過驅動力作用于副齒輪的柄上,驅動力進入差速器。驅動副齒輪和大的環行齒輪互相咬合,從而使環行齒輪和副齒輪一起旋轉。</p><p> 環行
25、齒輪上(穿過差速裝置)是一個差速副齒輪柄,柄上是兩個差速副齒輪。每個后車輪上各有一個車軸,兩個車輪的內側邊緣都有兩個齒輪夾板。這兩個差速副齒輪和兩個邊緣齒輪互相咬合。當車在公路上直線行駛時,兩個差速副齒輪不在副齒輪柄上旋轉,但是它們施力于兩個邊緣齒輪,從而使邊緣齒輪和環行齒輪速度相當,使兩個后車輪在轉彎時速度相同。差速裝置由兩個滾動的副軸承支持。這個裝置可以從一邊到另一邊進行調節用以在環行齒輪,副齒輪和副軸承之間提供反撞。通過螺絲軸承的
26、調節和每一邊墊片的代替,這種調節得以實現。</p><p> 橫軸最后讓齒輪提供傳輸,傳輸使轉矩和傳輸車軸的差速部分相連。傳輸車軸的差速部分和RWD車軸的差速齒輪有相同的組成部分,基本上以相同的方式運轉。這種力使火車和輪子在同一直線上,因此差速部分不需要以90度角轉彎。</p><p> 當車曲線行駛時,外輪要比內輪轉得快。為了保證這一點,兩個副齒輪在其柄上旋轉,向外輪提供比內輪更多的
27、動力。但是,外輪車軸的邊緣齒輪比內輪邊緣齒輪轉得快。這就保證了車轉彎時外輪比內輪轉得快。車軸有兩種基本類型:固定車軸和活動車軸。固定車軸不能旋轉;輪子在上面旋轉。以馬車為例?;顒榆囕S和輪子在一起,從而使兩個輪子和車軸一起旋轉。活動車軸根據他們支持的方式分類;半活動,四分之三活動和全活動。</p><p><b> 推進器柄和聯軸節</b></p><p> 推進器
28、柄是一種驅動柄,能使力傳輸?shù)胶筝嗆囕S。它連接傳輸主柄,通過推進器柄帶動到后車軸的差速裝置。主柄的傳輸旋轉通過推進器柄到差速裝置,使后車輪旋轉。</p><p> 推進器的設計必須將以下兩個因素考慮在內。首先,發動機和傳輸裝置的堅硬度要和車框差不多。其次,后車軸裝置(包括車輪和差速裝置)通過發條連接到車框。當后車輪在公路上違規,發條擠壓或膨脹。這就改變了驅動以傳輸和差速裝置之間的距離,并且推進器柄會照應這兩種變化
29、。這就是說,后車軸裝置,差速裝置和輪子,上下移動,傳輸柄之間改變。推進器柄縮短的原因是后車軸和差速移動的弧比推進器柄的小。車軸裝置弧的中心點是連接到框架后發條或控制臂。為了使推進器柄適應這兩個變化,必須有兩個獨立的裝置。這必須有一個或更多的聯軸節以保證裝置的多樣化。必須有一個滑動節保證推進器柄改變長度時的效率。</p><p> 推進器柄可以是實的也可以是空的,由一個管子維持著。一些施用包括推進器中心或附近那些
30、支持柄的軸承。這個兩部分推進器由中心軸承和聯軸節一起支持。在雙鉸鏈中聯軸節是必不可少的,它包含兩個Y型軛,一個在驅動柄上,另一個在被驅動柄上,還有個十字形裝置叫星形輪。星形輪的四臂叫耳軸,集中在兩個柄軛的終端。驅動柄使星形輪旋轉,星形輪上的另兩個耳軸使驅動柄轉動。當兩個柄互相疊壓時,軛的軸承保證軛在每個耳軸上旋轉。多種聯軸節已經用于汽車中,但是通用的種類只有星形輪和雙軛輪,速效輪,和球耳軸聯節。</p><p>
溫馨提示
- 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
- 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
- 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
- 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
- 5. 眾賞文庫僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
- 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
- 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。
最新文檔
- 車輛工程外文翻譯
- [雙語翻譯]車輛汽車差速器外文翻譯--汽車差速器設計的最新進展
- 外文翻譯--驅動橋和差速器
- 車輛工程外文翻譯----傳輸方式和操作
- [雙語翻譯]車輛汽車差速器外文翻譯--汽車差速器設計的最新進展(英文)
- 車輛工程外文翻譯 2
- 外文翻譯--驅動橋和差速器 (2)
- [雙語翻譯]車輛汽車差速器外文翻譯--汽車差速器設計的最新進展中英全
- 車輛工程外文翻譯---制動系統
- 車輛工程專業外文翻譯7
- 車輛工程外文翻譯--- 懸架系統
- 驅動橋和差速器外文文獻翻譯.doc
- 驅動橋和差速器外文文獻翻譯.doc
- 驅動橋和差速器外文文獻翻譯.doc
- 驅動橋和差速器外文文獻翻譯.doc
- 驅動橋和差速器外文文獻翻譯.doc
- 外文翻譯--驅動橋-差速器
- 2013年車輛汽車差速器外文翻譯--汽車差速器設計的最新進展
- 車輛工程外文翻譯--日常汽車保養
- 車輛工程外文翻譯---汽車懸架
評論
0/150
提交評論