材料成型及控制工程專業畢業設計（論文）外文翻譯

1、<p><b>　　中文2500字</b></p><p><b>　　本科畢業設計 翻譯</b></p><p>　　學生姓名：*****</p><p>　　班 級：*****班</p><p>　　學 號：*****</p><p>　　學

2、院：材料科學與工程學院</p><p>　　專 業：材料成型及控制工程</p><p>　　指導教師：***** 副教授</p><p>　　2011年3月25日</p><p>　　Section 4 – Die Design and Construction Guidelines for HSS Dies</p>&l

3、t;p>　　General Guidelines for Die Design and Construction</p><p><b>　　Draw Dies</b></p><p>　　Higher than normal binder pressure and press tonnage is necessary with H.S.S. in order

4、to maintain process control and to minimize buckles on the binder. Dies must be designed for proper press type and size. In some cases, a double action press or hydraulic press cushion may be required toachieve the neces

5、sary binder forces and control. Air cushions or nitrogen cylinders may not provide the required force for setting of draw beads or maintaining binder closure if H.S.S. is of higher strength or </p><p>　　Draw

6、 beads for H.S.S. should not extend around corners of the draw die. This will result in locking out the metal flow and cause splitting in corners of stamping. Draw beads should “run out” at the tangent of the corner radi

7、us to minimize metal compression in corners, as shown in figure 16 on page 47.</p><p>　　Better grades of die material may be necessary depending on the characteristics of the HSS, the severity of the part ge

8、ometry, and the production volume. A draw die surface treatment, such as chrome plating, may be recommended for outer panel applications.</p><p>　　Form and Flange Dies</p><p>　　Part setup in for

9、m and flange dies must allow for proper overbend on all flanges for springback compensation. Springback allowance must be increased as material strength increases; 3 degrees for mild steels, but 6 degrees or more for HSS

10、.</p><p>　　Punch radii must be fairly sharp. 1t for lower strength steels. Higher strength steels may require larger radii, but keeping them as small as practical will reduce springback in the sidewalls.<

11、/p><p>　　Flange steel die clearance must be held to no more than one metal thickness clearance to reduce springback and sidewall curl.</p><p>　　Form and flange steels should be keyed or pocketed in

12、 the casting to avoid flexing.</p><p>　　Flange steels should be designed to wrap over and coin the flange break in order to set the break and reduce springback. See figure 17 on page 48. </p><p>

13、;　　Die strength must not be compromised with light-weight die construction. High strength steel will require a stiffer die to resist flexing and the resultant part distortions, especially for channel or “hat-section” par

14、ts. This type of part can also cause serious die damage if double blanks occur.</p><p>　　Cutting Dies</p><p>　　To reduce press tonnage requirements and extend die life, a minimum shear of four t

15、o six times metal thickness in twelve inches of trim steel length is recommended.</p><p>　　To reduce die maintenance, maximum trim angles should be about 5° to 10° less than those used for mild ste

16、el. Trim steels should be keyed or pocketed in casting to avoid flexing. Die clearance should be 7 to 10% of metal thickness.</p><p>　　Drawbead Types</p><p>　　Conventional Drawbeads

17、 Run-out Drawbeads For H.S.S.</p><p>　　Lock Beads for Stretch-Form Die</p><p><b>　　Figure 16</b></p><p>　　1. Providing a vertical step in the flange stiffens and straigh

18、tens the flange, stopping sidewall curl as well as springback.</p><p>　　2. The addition of stiffening darts helps maintain a 90-degree flange.</p><p>　　3. By adding a horizontal step along the f

19、lange, the flange is stiffened, resulting in reduced springback.</p><p>　　4. Back relief on the upper flange steel allows for extra pressure to be applied futher out on the formed radius.</p><p>

20、;　　Section 5 – Die Tryout Guidelines for High Strength Steel Dies</p><p>　　General Guidelines for Die Tryout</p><p><b>　　Draw Dies</b></p><p>　　Higher draw die binder pr

21、essure and press tonnage will be necessary in order to maintain process control and draw parts without buckles. A double action press or a press with hydraulic cushion may be required in some cases to achieve the require

22、d binder forces.</p><p>　　HSS draw die operations will require sheet steel lubricants that are formulated for extreme pressures. Mill oils will not provide sufficient lubricity for most applications. Pre-lub

23、es or dry film lubricants may be necessary for process control.</p><p>　　Die plan view punchline corner radii should be larger than with mild steels to avoid buckling in the corners of the binder.</p>

24、<p>　　Stretch Form Dies</p><p>　　Lock beads may require modification to avoid cracking or tearing with higher strength grades of HSS. Opening side walls of beads and enlarging corner radii will avoid c

25、racking of high strength sheet steel. Lock beads should be continuous around the punchline for stretch form dies.</p><p>　　For large panels from stretch-form dies, such as a roof panel or hood outer, elastic

26、 recovery may result in a shrunken panel that does not fit well on the male die member of the trim or flange dies. This problem is corrected by adding a “plus” factor to the overall part dimensions of the draw die or str

27、etch form die punch. This “plus” is usually no more than 2.5 mm at the center of the sides and the front, tapering to 0.0mm at the corners of the part profile on the punch. Finish part profile is </p><p>　　F

28、orm and Flange Dies</p><p>　　The punch radius should be fairly sharp with 1 or 2t used for lower strength steel. HSS may require larger radii, but as small as practical to reduce springback of sidewalls.<

29、/p><p>　　The flange steel radius affects sidewall curl and springback on any offset flanges. This radius should also be small to reduce springback of side flanges.</p><p>　　Overbend for springback

30、compensation must be increased as tensile strength increases: 3 degrees is standard for mild steels, but 6 degrees or more will be required for HSS.</p><p>　　Flange steel die clearance should be tight, maint

31、aining no more than one metal thickness clearance to reduce springback and sidewall curl.</p><p>　　Cutting Dies</p><p>　　To reduce press tonnage requirements and extend die life, a minimum shear

32、 of four to six times metal thickness in twelve inches of trim steel length is required.</p><p>　　Die clearance should be 7 to 10% of metal thickness for HSS.</p><p>　　To reduce trim steel maint

33、enance, reduce maximum trim angles by about 5° to 10° from those used for mild steel. Trim steels should be keyed or pocketed in the casting to avoid flexing.</p><p>　　Die Tryout When Using Bake Ha

34、rdenable Steel</p><p>　　In order to obtain the maximum benefits of BHS, tryout of the dies should be performed as follows: Circle grid analysis must be performed on a panel before any die rework is attempted

35、. With the gridded panel as a reference, the die can be modified to provide a minimum biaxial stretch of 2.0%. Stretch-form or draw dies are best for this material.</p><p>　　For rough or functional tryout, i

36、t is possible to use mild steel with a 6% to 8% gauge increase to perform the normal process of die preparation. This alleviates complications when the BHS strengthens between each die being tried out. The reason for thi

37、s is the time lag that normally occurs between a panel being formed and its use in the next operation.</p><p>　　When the entire line of dies is ready for approval, all dies must be set in line. Panels should

38、 be run through all the die operations consecutively. This will avoid some of the strengthening effects of time delays between stamping operations that can cause variation in panels. Dimensional approval of the panel wil

39、l be most difficult if this procedure is not followed.</p><p>　　The strengthening reaction in the BHS can cause dimensional variation in flanges since springback will vary with time as the strength increases

40、. This is why running the panel through all die operations consecutively is crucial to a successful buyoff.</p><p>　　Part Buyoff</p><p>　　To reduce the part buyoff time and eliminate many hours

41、of tryout time, the benefits of functional build must be considered. This procedure has been proven to save time and money by concentrating on an acceptable sub-assembly rather than making each stamping to part specifica

42、tions. Those parts that are easiest to change are revised to suit the sub-assembly dimensional targets. Those parts that do not affect the sub-assembly quality are not changed, but the detail part specifications are revi

43、sed.</p><p>　　In addition to saving tryout time and die rework costs with functional build, lower part variation can also be realized. Two dimensional challenges faced by the die maker when first trying out

44、dies are to reduce the dimensional variation from nominal specifications, and to reduce the short term variation</p><p>　　from part to part. The typical priority is to first minimize part-to-part variation a

45、nd later address nominal deviation. A strong argument for this strategy is that the deviation from nominal is not precisely known until a dimensionally consistent part can be evaluated. The results are a dimensionally co

46、nsistent part even though a number of checkpoints may deviate from nominal, and perhaps even be out of tolerance. In many situations when dimensions on the die are reworked to shift them closer t</p><p>　　Fo

47、r more information on functional build, refer to the Auto/Steel Partnership publication. “Event-Based Functional Build: An Integrated Approach to Body Development”.</p><p>　　第四節-高強度鋼模具設計和制造指南</p><

48、p>　　對模具設計和制造的一般準則</p><p><b>　　拉深模具</b></p><p>　　為了控制高強度鋼的成形并減少板料邊緣的彎曲，高強度鋼成型時的壓力和噸位高于一般情況是必要的。模具設計必須考慮適當?shù)膲毫︻?lèi)型和尺寸。在某些情況下，為了達到需要的壓邊力和控制力可以用一種雙動壓力墊或液壓墊。如果高強度鋼有更高的強度和厚度，空氣墊子或氮?dú)飧卓赡芴峁┎涣?/p>

49、固定拉深筋或保持邊緣固定的力。</p><p>　　高強度鋼拉深筋不應該在拉伸模具的轉角處延長，這將會導致金屬流動被鎖定和在沖壓件角落處產生開裂。拉深筋應該“遠離”轉角半徑切線以減小金屬在轉角處壓縮,如圖16。</p><p>　　基于高強度鋼的特性、重要部位的幾何結構和生產量，選用好的材料制造模具是必要的。拉深模的表面處理,例如電鍍，可推薦用于外板的應用。</p><

50、p><b>　　脹形和翻邊模</b></p><p>　　為了能補償回彈量，用脹形和翻邊模生產的零件必須允許適當?shù)倪^(guò)度彎曲?；貜棙O限必須隨材料強度增加而增加;3度適用于低度鋼,但6度或以上適用于高強度鋼。</p><p>　　沖床半徑必須相當尖銳。低強度鋼1噸位。高強度鋼可以要求更大半徑,但使保持和實際生產時一樣小，可以降低側壁的回彈。</p>&

51、lt;p>　　翻邊模具間隙必須不超過一個金屬厚度間隙以降低回彈及側壁發生的卷曲。</p><p>　　脹形和翻邊板材要固定在鑄件里以避免發生撓曲。</p><p>　　翻邊板材應設計時應包住和壓住邊緣斷處以設置中斷和減少回彈。見圖17。</p><p>　　模具強度不能小于低強度模具結構的強度。高強度鋼將會需要一個堅硬的模具來抵抗屈曲和相應部分的扭曲,尤其是對

52、集中力處或冒形截面部分。這部分在成形多個毛坯時也會引起嚴重的模具損壞</p><p><b>　　剪切模具</b></p><p>　　為了降低噸位要求和延長模具壽命,十二英寸長的金屬至少修剪四到六次。</p><p>　　為了減少模具的維修,最大修剪角應該在5°角到10°，應該低于使用低碳鋼的角度。修剪鋼材要固定在鑄件中以

53、避免鑄件撓曲。模具間隙應該是7%到10%的金屬厚度。</p><p><b>　　拉延筋的類型</b></p><p>　　傳統的拉延筋 高強度拉延筋</p><p><b>　　帶壓邊圈拉延模具</b></p><p>　　1.提供一個垂直的臺階來強化和

54、壓制邊緣,同時防止側壁的卷曲以及回彈。</p><p>　　2.增加強化暗褶有助于維持一個90度邊。</p><p>　　3.通過沿邊緣添加一個橫向的臺階、能強化邊緣并減少回彈。</p><p>　　4.上邊緣金屬的補充使得額外的壓力能夠進一步應用于形成的半徑上。</p><p>　　第五節 高強鋼模具的模具調試</p><

55、;p>　　對模具調試的一般準則</p><p><b>　　拉深模具</b></p><p>　　為了控制高強度鋼成型控制并減少板料邊緣的彎曲，在高強度鋼成型時壓力和噸位高于一般情況是必要的。在某些情況下，為了達到需要的壓邊力和控制力可以用一種雙作用壓力墊或液壓墊。</p><p>　　高強度鋼拉深模操作時需要用于制定極端的壓力鋼板潤滑劑

56、，機油對于大多數應用將不提供足夠的潤滑性。預先潤滑或干膜潤滑油對拉深過程控制有必要的作用。</p><p><b>　　拉伸成型</b></p><p>　　對于有高強度的高強度鋼定位調整桿可能需要修改以避免斷裂或撕裂。開放側面轉角半徑的筋和擴大轉角半徑將避免高強度鋼板的開裂。定位調整桿應連續圍繞在延伸模的延伸方向上。</p><p>　　延伸

57、模對于大型嵌板,如車頂或外罩，彈性的回復可能導致板面的收縮,以至于與凸模和翻邊模不匹配。通過添加一個因素的來增大拉深模具或翻邊部分尺寸來糾正這個問題。這個“添加的因素”是在該中心的側面和前面增加不超過2.5毫米,沖頭上轉角處部分的錐度是0，在總的翻邊模中，通過邊界部分的剖面,增加的部分被移走。</p><p><b>　　脹形和翻邊模</b></p><p>　　沖頭

58、半徑應比較突出尖銳，低強度鋼用1或2噸位。H.S.S.可能需要更大半徑,但減小到使用時能減少側壁回彈。</p><p>　　在任何平板翻邊中翻邊鋼材會影響回彈和側壁的卷曲。半徑應該也小到可以減少邊緣的回彈。</p><p>　　過度彎曲時回彈補償必須隨抗拉強度增加而增加:3度對于低強度鋼是一種標準,但6度或以上將會被用于H.S.S。</p><p>　　翻邊模模具間

59、隙應該緊湊,保持間隙不超過一個金屬厚度以減少回彈及側壁的卷曲。</p><p><b>　　剪切模</b></p><p>　　降低噸位要求和延長模具壽命,十二英寸長的金屬至少修剪四到六次。</p><p>　　對于高強度鋼模具間隙應在7% - 10%的金屬厚度。</p><p>　　減少模具的維修,最大修剪角應該在5&

60、#176;角到10°，應該低于對低碳鋼的使用角度。修剪鋼材要固定在鑄件中以避免在鑄件撓曲。</p><p>　　當使用加熱可硬化鋼材的模具試用</p><p>　　為了獲得使用BHS的最大值,模具應進行如下:在行任何模具重新工作前都必須嘗試分析圓網格。模具可作為一個參考網格板料、模具可修改提供的最小二軸的伸展2.0%。延伸?；蚶炷＞咦钸m合該材料。</p><

61、p>　　粗糙度或功能調試,它可以用低碳鋼增加6% -8%標準來來表現通常模具的準備過程。這能減輕在每個模具調試時BHS得到強化時的復雜情況。這一現象的原因可能是時間滯后,通常一個板料之間發生的形成及其用于下一個操作。</p><p>　　當整個系列的模具已準備就緒，所有的模具必須設置在一條線上。板料能在所有的模具連續操作。這將避免一些加固效果的時間延遲操作,可以引起沖壓件之間變化。如果這個過程是不被允許的那

62、么尺寸的延伸將是最困難的。</p><p>　　BHS的變化會導致邊緣尺寸的變化,因?yàn)殡S時間回彈將隨強度的增加而增加。這就是為什么讓板料能連續通過模具各部分，對一個成功的檢查來說是至關重要的。</p><p><b>　　部分新產品引入</b></p><p>　　為了減少新產品引入時間和消除幾個小時的調試時間,就要考慮功能建設所有的優勢。這個

63、應用程序被證明能節省時間和金錢通過專注于一個可接受的半成品,而不是迫使每個沖壓分開進行。這些零件是最容易改變來適應半成品進行相應的修正尺寸的目標。這些部分并不足以影響半成品質量，但是細節部分規格被修改。如果將這種程序用于高強度鋼沖壓件新產品引入將會消耗過多時間。</p><p>　　在功能的建立中除了節省時間和模具調試成本,降低零件變化都有可能實現。模具制造商所面臨兩個尺寸上的挑戰：當?shù)谝淮螄L試模具時相對于公稱規

64、格降低尺寸上的變化,降低了各部分間的短期尺寸變化。首要任務是要先減小零件間變化和偏差。這個策略一個強有力的論點認為偏離標稱是被允許的直到零件尺寸上一致可以評估。盡管很多測試點偏離標準位置有的甚至超過偏差極限但在結果上它們尺寸上是一致的。在許多情況下當改變模具尺寸使它接近標準值,它們變得不穩定甚至導致部分間更大的變化。這功能建設理論評估零件變穩定后可接受程度,在小尺寸上的進行改變。即使功能的建立在模具重做時也會有大偏差或臨界尺寸出現?；?/p>