畢業設計論文中型換熱片用沖壓模具設計

1、摘 要I摘 要本論文根據產品圖樣，分析沖裁件的形狀、特點、尺寸大小精度要求、表面質量及所用材料等沖壓工世性，在此基礎上，分別設計復合模 及壓紋等單工序模具，實現流水線作業。流水線作業是本次設計的亮點所在。凸模采用成型加工或線切割，沖裁部分進行熱處理，由螺釘固定，剛性推件，彈性卸料裝置橡膠的彈性把料板由下而上推出，隨上模的動作而動作，運動平穩可靠且不易損壞模具，采用中間導柱圓形有利用安裝，且因安裝不當而造成模具損壞，根據沖壓力選擇開式

2、固定臺壓力機。關鍵詞 關鍵詞：沖裁件；級進模；設計 目 錄III目 錄摘 要...............................................................................................................................................IAbstract .........................

3、...................................................................................................................II第一章 概述 ...............................................................................................

4、...................................11.1 板式換熱器的介紹 ............................................................................................................11.2 國內外模具發展現狀 ................................................

5、........................................................2第二章 散熱片沖壓工藝性能分析...............................................................................................52.1 散熱片的介紹 .......................................

6、..........................................................................52.2 散熱片形狀尺寸 .............................................................................................................52.3 散熱片的工作原理 ........

7、.................................................................................................62.4 散熱片尺寸及精度要求 .................................................................................................62.5 散熱片

8、沖壓工藝性分析 .................................................................................................7第三章 模具方案的分析確定 ...................................................................................................

9、...73.1 方案一 .............................................................................................................................73.2 方案二 ........................................................................

10、.....................................................93.3 結論 ...............................................................................................................................11第四章 模具設計 ...................

11、.....................................................................................................124.1 沖孔模模具設計 ........................................................................................................

12、...124.1.1 確定合理的沖裁間隙 ................................................................................................134.1.2 沖壓壓力的計算 .....................................................................................

13、...................144.1.3 壓力機的選擇 ............................................................................................................144.1.4 凹凸模刃口尺寸的設計 .........................................................

14、...................................154.1.5 沖模閉合高度的確定 ................................................................................................154.1.6 螺栓選取和強度校核 ...................................................

15、.............................................154.1.7 銷釘選取和強度校核 ................................................................................................164.2 對稱導柱壓中間紋模具設計計算.......................................

16、.........................................174.2.1 沖裁壓力計算 ............................................................................................................174.2.2 壓力機的選擇 .......................................

17、.....................................................................184.2.3 模具間隙值的確定 ....................................................................................................184.2.4 凸凹模刃口尺寸的設計 .............

18、...............................................................................194.2.5 沖模閉合高度的確定 ................................................................................................194.2.6 沖模主要零部件的設計計算.....

19、................................................................................204.2.7 螺栓選取和強度校核 ................................................................................................214.2.8 銷釘選取和強度校核 ......

20、..........................................................................................214.3 中間導柱壓兩側紋模具的計算....................................................................................224.3.1 沖裁壓力計算 ..........

21、..................................................................................................224.3.2 壓力機的選擇 ..........................................................................................................

22、..224.3.3 模具間隙值的確定 ....................................................................................................234.3.4 沖模閉合高度的確定 .................................................................................

23、...............234.3.5 凸凹模刃口尺寸的設計 ............................................................................................234.3.6 沖模主要零部件的設計計算........................................................................