外文文獻翻譯、搖臂式煤礦救援機器人移動平臺外文翻譯、中英文翻譯

1、<p><b>　　翻譯部分：</b></p><p><b>　　英文原文</b></p><p>　　Mobile platform of rocker-type coal mine rescue robot</p><p>　　LI Yunwang, GE Shirong, ZHU Hua, FANG Ha

2、ifang, GAO Jinke</p><p>　　School of Mechanical and Electrical Engineering, China University of Mining & Technology, Xuzhou 221008, China</p><p>　　Abstract: After a coal mine disaster, especi

3、ally a gas and coal dust explosion, the space-restricted and unstructured underground terrain and explosive gas require coal mine rescue robots with good obstacle surmounting performance and explosion-proof capability. F

4、or this type of environment, we designed a mobile platform for a rocker-type coal mine rescue robot with four independent drive wheels. The composi- tion and operational principles of the mobile platform are introduced,

5、we discuss the f</p><p>　　1 Introduction</p><p>　　In the rescue mission of a gas and coal dust explosion, rescuers easily get poisoned in underground coalmines full of toxic gases, such as high-

6、concentration CH4 and CO, if ventilation and protection are not up to snuff. Furthermore, secondary or multiple gas explosions may be caused by extremely unstable gases after such a disaster and may cause casualties amon

7、g the rescuers[1]. Therefore, in order to perform rescue missions successfully, in good time and decrease casualties, it is necessary to</p><p>　　2 Mobile platform[11-12]</p><p>　　Of As shown in

8、 Fig 1, the mobile platform of the rocker-type four-wheel coal mine rescue robot includes a main body, a gear-type differential device,two rocker suspensions and four wheels. The the shell of the differential device is a

9、ttached to the interior of the the main body The two extended shafts of the differential device are supported by the axle seats in the of lat-to early plate of the main the body and connected to the rocker suspensions in

10、stalled at both sides of the main the body. of</p><p>　　2.1 Rocker suspension</p><p>　　2.1.1 Function</p><p>　　The primary role of the rocker suspension is to provide the mobile pla

11、tform with a mobile system that can adapt to the unstructured underground terrain,such as rails, steps, ditches and deposit of rock and coal dumps because of the collapse of the tunnel roof after a disaster. By connectin

12、g the differential device intermediate between the two rocker suspensions, the four drive wheels can touch the uneven ground passively and the wheels can bear the average load of the robot so that it is able to</p>

13、<p>　　2.1.2Structure</p><p>　　As shown in Fig. 1, the rocker suspension is composed of a connecting block, landing legs and bevel gear transmissions. The angle between the landing legs on each side of

14、 the main body is carefully calibrated. The legs are connected to the connecting block and the terminals, which in turn are connected to the bevel gear transmissions. Fig. 2 illustrates the cal. The DC motor is in the le

15、g and fixed to the connecting cylinder. The motor shaft connects to the bevel gear transmission and the wheel </p><p>　　A coal mine environment is full of explosive gases;hence, a rescue robot must be design

16、ed to be flame-proof. The DC motors, for driving each wheel, are installed in the landing legs of the rocker suspensions.At the present low-powered DC motors, available in the market, are of a standard design and not fla

17、me-proof, hence a flame proof structure for these motors must be designed. Given the structural features of the rocker suspension, it is very much necessary that a flame proof design for the la</p><p>　　Ther

18、e is also a flameproof connection cavity in the upper section of the leg. In order to save space, the guidance wire is sealed together with the wire holder using a sealant. The seat of the guide wire is installed in the

19、hole of the upper section of the landing leg.Another flameproof joint is formed between the wire holder and the hole. The cavity of the upper section connects to the rabbet structure of the bottom section, with yet anoth

20、er flameproof joint. There is a flame-proof cable entry </p><p>　　2.2 Differential device[13-15]</p><p>　　2.2.1 Characteristics of the differential mechanism The differential Mechanism of a roc

21、ker-type robot is a motion transfer mechanism with two degrees of freedom, which can transform the two rotating inputs into a rotating output. The output is the linear mean values of the two inputs. If we let 1 and 2 be

22、two angular velocity inputs,the angular velocity output, ω1 and ω2，wo rotational angle inputs and ω be rotational angle output, we have:</p><p><b>　　， </b></p><p>　　Two rotational i

23、nput components connect to the left and the right rocker suspension of the robot and the output component connects to the main body of the robot. In this way, the swing angles of the left and right rocker suspensions are

24、 averaged by the differential mechanism and the mean value, transformed into the swing angle (pitching angle) of the main body, is the output. It is effective in decreasing the swing of the main body and thus reduces the

25、 terrain effect. Taking the main swing angle</p><p>　　2.2.2 Principle of the bevel gear differential mechanism</p><p>　　Fig. 3 shows the schematic diagram of the bevel gear differential mechanis

26、m. Two semi-axle bevel gears 1 and 2 mesh with the planetary bevel gear 3 orthogonally. Carrier H connects to planetary bevel gear 3 coaxially. Let the angular velocities of gears 1,2, 3 and carrier H be ω1、ω2、ω3 and ωH

27、. Let the number of their teeth be Z1 , Z 2 and Z3 , where Z1, Z2 . Let the rotational angles of gear 1, 2 and carrier H be φ1、φ2、φH . If we let the relative H then we have:</p><p>　　We obtain and </

28、p><p>　　2.2.3 Bevel gear differential device</p><p>　　Given the above principle of a bevel gear differential mechanism, we designed such a bevel gear differential device, shown in Fig. 4. Fig. 4a i

29、s the outline of the differential device, and Fig. 4b its internal</p><p>　　Structure.This bevel gear differential device is composed of a shell, end covers, an axle base, semi-axle bevel gears, planetary be

30、vel gears, a connecting shaft, etc.The end covers and axle beds connect to the shell by screws. In the shell, two planetary bevel gears are coaxial and symmetrically installed at the connecting shaft, with the shaft term

31、inals supported at the end covers. There are bearings between the connecting shaft and bevel gears. The circlips are installed on the connecting shaf</p><p>　　Let the pitch and horizontal roll angle be α and

32、β ,then the maximum allowable pitch and horizontal roll angle are as follows:</p><p>　　The weight of the robot platform is 20 kg and its maximum load capacity is 15 kg. The robot platform is driven by four D

33、C motors with 60 W power. Its maximum speed is 0.32 m/s.</p><p>　　3 Mobile platform test</p><p>　　3.1 Simulation test</p><p>　　An accurate, simulated 3D model of the robot was Impor

34、ted into the ADAMS software. Using the kinematic pairs in the joints database of the ADAMS/View, the movement of each part of the simulation model is constrained. For simulating the differential action of differential de

35、vices acting on the robot body, a revolute joint between the left and right rockers of the model and the “Ground” is established. Random moments of forces are exerted to the left and right rockers to simulatethe rough ac

36、tion o</p><p>　　exerted to the pair of gears of the differential device.After corresp- </p><p>　　onding marker points on the robot are established, the swinging angles of the left and right rock

37、ers and the robot body are measured and the</p><p>　　curves of the swinging angles along with the time are obtained via the ADAMS/Postprocessor module, shown in Fig. 6. Curves 1 and 2 are swing angle curves

38、of the two rockers, while curve 3 is the swingangle curve of the main body.</p><p>　　The bevel gear differential device can average theswing angles of the right and left rockers, and the average value is the

39、 swing angle of the main body.The gap between two teeth and other factors cause the return difference of the gear drive, so when the main body is swinging at the early start-up and through the zero angle, there is a slig

40、ht swinging angle deviation between the simulated and theoretical values.</p><p>　　Typical steps, channels, slopes and other complex terrain models are built in the SolidWorks software. For testing the traff

41、icability characteristics and ride comfort of the four wheel robot, all-terrains models are imported into the ADAMS software[16-17]. Then the joints and restraints are rebuilt, Contact Force between the terrain and the w

42、heels is exerted and torque is exerted to each wheel. The running condition of the robot is simulated on the complex terrain,as shown in Fig. 7a. The vertic</p><p>　　3.2 Prototype test</p><p>　　

43、In order to verify the performance of the robot in surmounting obstacles and adapting to a complex terrain, an obstacle-surmounting test of the robot was carried out on a simple obstacle course built in thelaboratory and

44、 on a complex outdoor terrain bestrewn with messy bricks and stones. Fig. 8 shows the video image of the robot when moving on the complex terrain.The tests indicate that the four drive wheels of the robot can passively k

45、eep contact with the uneven ground and the robot performed w</p><p>　　4 Conclusions</p><p>　　Coal mine accidents, especially gas and coal dust explosions, occur frequently. Therefore, it is nece

46、ssary to investigate and develop coal mine rescue robots that can be sent into mine disaster areas to carry out tasks of environmental detection and rescue missions after </p><p>　　disasters have occurred, i

47、nstead of sending rescuers which might become exposed to danger.</p><p>　　2) An underground coal mine environment presents a space-restricted, unstructured terrain environment,with a likely explosive gas atm

48、osph- ere after a disaster.Hence, any mobile system would require a high motion performance and obstacle-surmounting performance oncomp- ex terrain.</p><p>　　3) Given an unstructured underground terrain envi

49、ronment and an explosive atmosphere, we investigated an explosion-proof coal mine rescue robot with four independent drive wheels, based on a rocker type structure. Our simulation and test results indicate that the robot

50、 performs satisfactorily, can passively adapt to uneven terrain, is self adaptive and performs well in surmounting obstacles.</p><p>　　4) In our study, we only investigated the rocker-type mobile platform of

51、 a coal mine rescue robot. In order to adapt to the underground coal mine environment,we also carried out a flameproof design for the main body. It was necessary to improve the rocker suspensions in order for the robot t

52、o be able to adjust the angle between two landing legs automatically, so that the height of the center of gravity of the robot can be controlled, which should improve the anti-rollover performance of the robo</p>

53、<p><b>　　中文譯文</b></p><p>　　搖臂式煤礦救援機器人移動平臺</p><p><b>　　摘 要</b></p><p>　　煤礦災害之后，尤其是氣體和煤塵爆炸后，地下空間限制和非結構化的地形以及爆炸性氣體的存在，需要具有良好的越障性能和防爆穩定性的煤礦救援機器人。對于這種類型的環境，

54、我們設計了四個獨立的搖臂式煤礦救援機器人移動平臺和獨立驅動的車輪。介紹了移動平臺的組成和運作方式，我們討論了礦用隔爆型設計搖臂以及它的運行方式和錐齒輪差速器的機械結構。使用ADAMS軟件模擬了不平坦的虛擬地形對機器人進行仿真實驗。仿真結果表明，差動裝置能保持一個機器人的主體在搖晃中的平衡。機器人模型具有良好的實用價值。對機器人原型已經進行了地形的適應性和越障性能的實驗。結果表明，樣機具有良好的地形的適應性和強大的越障性能。關鍵詞：煤礦

55、救援機器人；搖臂懸掛；特殊性；防爆設計</p><p><b>　　1 介紹</b></p><p>　　在瓦斯和煤塵爆炸的事故中執行救援任務，救援人員容易在充滿有毒的氣體的煤礦井下中毒，如高濃度CH4和CO，如果保證不了通風就會出現事故。此外，多種氣體混在一起形成極不穩定的混合氣體引發爆炸，并可能造成救援人員傷亡[1]。因此，為了執行救援任務成功，爭取救援時間和減少

56、傷亡，就必須發展煤礦救援機器人。機器人代替了救援人員進入災區和執行任務的環境檢測、搜尋受傷的礦工和災難發生后的幸存者。</p><p>　　這個機器人搜救工作的首要任務是進入災區。這是困難的機器人進入限制空間和非結構化的地下地形，所以這些移動系統需要很好的越障性能和運動性能在這種惡劣環境執行任務[2]，使用一些傳感器能夠在低能見度和充滿爆炸性氣體和塵埃的環境下完成對地形的識別；因此，假定的移動系統應該盡可能是獨立

57、的傳感器和控制系統[3]。國內和國外煤礦救援機器人的研究才剛剛起步。大多數機器人原型都是簡單的輪式和跟蹤機器人。桑迪亞國家實驗室智能系統和機器人技術中心(ISRC)所開發的礦山勘探機器人RATLER，使用的是輪式移動系統[4]?？▋?nèi)基梅隆大學的機器人研究中心開發了一個自治的礦藏的開采機器人，稱為“Groundhog”[5]。由 Remotec 公司制造的 V2 煤礦井下搜救探測機器人和中國礦業大學的CUMT-1，使用一個雙履帶的移動系統

58、[6-7]。這四個樣品都受到地下煤礦環境的嚴重限制。搖臂式機器人在復雜的地形下已經具有良好的性能。所有三個火星探測器，“索杰納”、“勇氣號”、“機遇號” 火星車均采用了六輪獨立驅動的搖桿-轉向架移動系[8-9]。美國噴氣推進實驗室開發出來的Rocker-Bogie，實驗成功登陸上火星</p><p>　　2 移動平臺[11]</p><p>　　圖1所示，移動平臺的搖臂式四輪煤礦營救機器人

59、包括一個主體，齒輪式差動設備，兩個搖臂懸掛和四個輪子。外殼通過差動設備連接到內部主體。差動的兩個擴展槽設備支持在橫向的軸座板的主體，并連接到兩邊的安裝搖臂懸浮主體上。四個輪子分別連接到錐齒輪傳動終點站四個著陸的腿。四個輪子都是獨立的由一個直流電機驅動，安裝在著陸腿懸掛的搖臂下。一個用隔爆型設計腿已經制定，其中包括用隔爆型電機腔和隔爆型連接腔。通過電纜入口裝置，電源和控制直流電動機的電纜連接到電源和控制器的主體。 </p>

60、<p><b>　　2.1搖臂懸掛</b></p><p><b>　　2.1.1功能</b></p><p>　　搖臂懸架的主要作用是提供的移動系統能適應非結構化井下地形的移動臺，像軌道，臺階，壕溝和巖石的礦床等由于隧道頂部倒塌的煤炭傾倒災難發生后。通過連接差動裝置中間之間的兩個搖臂懸浮液，四個驅動輪可以接觸到凹凸不平的地面被動車輪可

61、以承受的平均負載機器人，所以，它是能夠跨越軟地形。車輪可以提供足夠的推進力，使機器人通過超越不均勻的障礙，并通過地形。</p><p><b>　　2.1.2 結構</b></p><p>　　正如圖1所示，搖臂懸掛組成連接塊，著陸腿和錐齒輪傳動。著陸之間的角度每個主體一側的腿被仔細校正。腿被連接到連接塊和終端，這反過來又連接錐齒輪傳動。圖2說明結構降落腿。它分為上層

62、和底部。底部是圓柱。直流電動機是在腿和固定連接缸。電機軸連接到錐齒輪傳動和輪也連接傳輸。上部有中心盲孔連接是通過箕舌線形成的底部，通過連接腔。通過電纜入口裝置的上半部分，從主電機功率和控制電纜機器人的身體被放到連接腔并連接到接線端子，反過來，連接線持有人的指導線。另一個指導線的一端連接在電機的底部。</p><p><b>　　2.1.3防爆設計</b></p><p&g

63、t;　　一個煤礦環境充滿爆炸性氣體；因此，營救機器人必須設計為隔爆型。直流電機，用于驅動每個輪子，是安裝在著陸的腿搖臂中。在目前的低功率的直流電機，可選市場，是標準的設計而不是防爆、因此一個防爆結構對于這些汽車必須設計。給定的結構特點搖臂懸架，它非常有必要防爆設計為著陸的腿被執行。</p><p>　　有兩個重要的問題需要考慮這型礦用隔爆型設計。首先，需要一個防爆腔，在這種標準直流電機安裝。鑒于防爆設計要求，一群

64、關節型礦用隔爆型電動機應之間形成軸和傳動軸洞。通常，電機軸由制造商太短的遵守防爆關節的要求，因此電機軸需要擴展。其次，采用防爆連接型腔應設計成領導電纜到連接腔通過隔爆型電纜條目設備。直流電機，尤其是有刷直流電機，可能產生的火花在正常運行和當電機負載很高，工作電流可能超過5A，這超過了當前的限制附錄C2中國國家標準的要求GB3836.2 -2000。因此，電動機電源和控制電纜不能直接在連接腔。</p><p>　　

65、考慮到這些要求，著陸的腿上有被設計為隔爆型單位，如圖2所示。一個細長軸套筒組裝而成的電機軸，在同樣的半徑內的電機軸，這是電機軸被擴展。前面的法蘭電機的固定在中聯板的連接缸。這個電機軸軸袖的經過中心孔嵌有黃銅布什然后連接到輸入齒輪傳動齒輪最后的底部的著陸腿。因此，隔爆型關節之間形成的電機軸和傳動軸套筒之間，以及軸套筒和黃銅。終端底部的腿的連接連接圓筒和隔爆型聯合組成外部圓柱表面之間的終端圓柱表面和內部的連接缸。</p>&l

66、t;p>　　還有一個防爆連接腔腿的上層。為了節省空間，指導線是密封連同電線持有人使用密封劑。導線的座位安裝在洞的著陸支架的上層。另一個防爆聯合間形成電線持有人和洞。上層的空腔連接到榫接結構的底部，用另一個防爆聯合。有一個防爆電纜入口設備結束時的上層著陸的腿。因此，隔爆型連接腔形成的上層的腿。</p><p>　　基于結構描述，標準直流汽車被安裝在隔爆型孔的腿的底部。電力和控制電纜電機的連接到防爆連接腔的上層

67、通過導線持有人。此外，電纜防爆主體機器人的連接到連接腔通過防爆電纜入口設備。因此，防爆設計的著陸支架的搖臂懸掛部分。</p><p><b>　　2.2 差動裝置</b></p><p>　　搖桿式機器人差動機構是一種二自由度運動轉換機構，能夠?qū)?個轉動輸入轉化為1個轉動輸出，且輸出為兩個輸入的線性平均值。設兩個輸入為轉速ω1、ω2， 輸出為轉速ω。， 兩個輸入為轉角

68、、輸出為轉角中， 則應滿足以下關系式：</p><p><b>　　， </b></p><p>　　將該機構的兩個輸入分別與機器人的左右搖桿部分連接， 將其輸出與機器人主車體連接， 這樣， 該機構可將機器人左右搖桿的擺角進行線性平均， 并轉化為機器人主車體的擺角輸出， 以保持機器人主車體的相對平衡， 有效地減小地形變化對主車體的影響。若把機器人主車體的擺角視為輸入，

69、 左右兩搖桿的擺角為輸出， 則該機構將此轉動輸入分解為兩個不同的轉動輸出， 則輸入為兩個輸出的線性平均值， 這樣有助于機器人較為均勻地向各個車輪分配車體重量， 且可使得各車輪能隨著地面的起伏被動地自由調整位置， 以適應復雜的地形環境。</p><p>　　圓錐齒輪齒合型差動機構的原理圖如圖3所示，兩中心錐齒輪1、2均與行星錐齒輪3正交齒合，系桿H支撐行星錐齒輪3。設齒輪1、2、3與系桿H的轉速分別為ω1、ω2、ω

70、3、ωH；齒輪的齒數分別為Z1、Z2、Z3，則Z1=Z2；齒輪1、2及系桿H的轉角分別為：φ1、φ2、φH，則錐齒輪1、2相對系桿H的傳動比為:</p><p><b>　　可得 和 </b></p><p>　　2.2.1 錐齒輪差速器裝置鑒于上述原則的錐齒輪差速器機制，我們設計了這樣一個錐齒輪差速器設備，如圖4。圖4a是大綱差速裝置外觀，圖4b其內部結構。它可

71、以清晰的看到這傘齒輪差動機制可以用于搖臂式移動機器人。</p><p>　　這錐齒輪差速器裝置組成外殼，端蓋，軸距，半橋錐齒輪，行星錐齒輪，連接軸，等等。端蓋和車軸的底座通過螺絲連接到外殼。兩個行星錐齒輪同</p><p>　　軸對稱的安裝在連接軸上，在底部支持軸終端覆蓋。軸和錐齒輪之間有軸承連接。擋圈安裝在連接軸上限制軸承的負荷。兩個半橋錐齒輪被分開安置在兩軸座上，兩軸座是對稱的固定在外

72、殼上的和兩個半橋錐齒輪網，兩個行星錐齒輪正交。兩橋基本上具有相同的結構。半橋位于錐齒輪的軸承，軸套在軸床擋圈上。當差動設備安裝在機器人上，兩軸連接到左邊和右邊的半橋錐齒輪左邊和右邊的搖臂。差動的外殼被固定在機器人的主體上。</p><p>　　2.3 機器人移動平臺的基本參數 </p><p>　　圖5顯示了領先的機器人平臺的基本參數。臂長360mm，腿間夾角，輪胎直徑d=200mm，軸距

73、，機器人寬i=670mm，搖臂中心高度，主體輪廓尺寸長a=400mm，高b=200mm，寬f=310mm，主體輪廓頂部離地高度c=522mm，重心離地高度h=360mm，搖臂擺動角度左（φ1）和右（φ2）范圍為（-45°~ 45°）。</p><p>　　令俯仰角和橫向側傾角為α和β，允許機器人的最大俯仰角和側傾角如下： </p><p>　　機器人平臺的重量是20公斤

74、，其最大負載能力是15公斤。機器人平由四個直流電動機驅動，功率為60瓦。其最大速度為0.32米/秒。</p><p>　　3 移動平臺測試3.1模擬試驗 </p><p>　　把一個精確地模擬機器人的三維模型導入ADAMS軟件。使用ADAMS對關節數據庫仿真結果表明，模擬的每個部分的運動模型的約束。對于模擬。</p><p>　　的差動器件的行動機器人身體，左

75、，右轉動聯合建立模型和“接觸地面”的搖臂。外力的隨機時刻的施加在左側和右側的搖臂上來模擬搖臂在粗糙的地形上行動。對于模擬的之變動精確性，接觸力差動設備充分發揮雙差動裝置齒輪。在機器人上的相應標記點成立后，通過ADAMS后處理模塊，擺動角度的左邊和右邊搖臂和機器人身體測量和隨著時間的擺動角度而獲得曲線，如圖6。曲線1和2是擺角兩個搖臂的曲線，而曲線3是差動裝置主體的角度曲線。</p><p>　　`錐齒輪差動裝置可

76、平均右側搖臂和左側搖臂的擺動角度，平均值為主體的擺角。輪齒之間的間隙是造成齒輪傳動回差之間的差距，所以在初期啟動經過零角度時，主體是搖擺不定的，仿真時在允許的角度之間有輕微的擺動的和理論上的偏差值。</p><p>　　使用SolidWorks軟件建立典型的階梯，壕溝，斜坡和其他復雜地形模型。用于測試四輪機器人的通過性的和平順舒適性，將全地形模型導入到ADAMS軟件[16-17]。然后重建關節和約束，接觸力地形和

77、車輪施加之間轉矩施加到每個車輪。運行條件機器人是仿真在復雜的地形上，如圖7a。垂直位移，身體速度的重心和加速度曲線四個輪子的中心，因?yàn)榭梢缘玫饺鐖D7b~7d所示。</p><p>　　根據曲線，主體的重心位移曲線（mainbody_d曲線）是非常順利的，速度和加速度是四個輪子的平均值。模擬結果表明，機器人移動平臺在復雜地形上具有良好的通過性和舒適性。</p><p><b>　　

78、3.2 原型試驗</b></p><p>　　為了驗證機器人的越障性能和復雜地形適應性，機器人越障測試在一個有簡單障礙物的實驗室內和一個有著凌亂的磚頭和石塊室外復雜環境中進</p><p>　　行的。圖8是截取機器人在復雜地形上移動時的視頻中的圖片。試驗表明，四個驅動輪機器人可以被動地保持與不均勻地面接觸和機器人克服移動時遇到的障礙。在不平的地面上移動時，主體中的差動裝置通過搖

79、臂能有效的減小主體的顛簸。機器人能跨越260毫米高的障礙。只有大搖臂支腿之間的障礙出現才會阻止前進。四個輪子的機器人的越障性能，顯然大于上一代同尺寸的履帶機器人。</p><p>　　4 結論1）煤礦事故，特別是天然氣和煤炭粉塵爆炸，頻頻發生。因此，研究和開發可以進入到礦難災區的煤礦救援機器人，完成環境監測和救援任務的使命，代替救援人員，減少二次災難的發生。2）受煤礦井下復雜環境空間的限制，非結構化的地形

80、環境，有可能在災難發生后存在著爆炸性氣體環境。因此，任何移動通信系統將需要很高的本安性能和必要的越障能力。3）鑒于非結構化地下的地形環境爆炸性氣體環境中，我們調查防爆煤礦救援機器人四個獨立驅動車輪，基于搖臂類型結構。我們的模擬和測試結果表明，機器人的表現令人滿意，可以被動地適應不平坦的地形，自適應性和越障性能表現良好。</p><p>　　4）在我們的研究中，我們只調查的搖臂式煤礦救援機器人的移動平臺。在為了