單片機外文翻譯永磁無刷直流電機

1、<p><b>　　BLDCM</b></p><p>　　BLDCM small size, light weight, it has a DC motor similar to the general good speed performance, without the existence of machinery for the device, electromagneti

2、c interference noise and small, low maintenance requirements, reliability, good; and as a result of not required excitation power, efficiency is relatively high, it has been rapid development. A company based on ADI'

3、s ADSP-21992 chip high-speed brushless DC motor control system, which has a high-speed, high load moment of inertia, have </p><p>　　DSP-based motor control system with the traditional single-chip motor contr

4、ol system and a dedicated chip motor control system, that is, a dedicated motor control mechanisms, user-programmable, scalable, and powerful, and so on; at the same time, overcome their respective shortcomings, such as

5、peripherals and memory integrated into the chip to reduce circuit board area, reducing the number of system components to improve the CPU processing capacity, improve system reliability. System, the ultima</p><

6、;p>　　Need to select the highest possible processing speed of the chip. 2199x series and ADI's speed reached 160 M, and then to adapt to take into account their poor working environment, in this paper, we have chos

7、en the ADSP-21992 as a core control chip.</p><p>　　(A) hardware</p><p>　　1. Control circuit</p><p>　　Mainly by the control circuit and its corresponding external ADSP21992 expansion

8、 circuit. Including the crystal oscillator circuit, extend outside the FLASH, JTAG interface, power supply voltage conversion circuit, PWM interface, 1 / 0 interface and A / D interface circuit modules. ADSP21992 for the

9、 160 M high-performance mixed-signal DSP chips, the chip in addition to a powerful data-processing capabilities, for motor control, but also to provide 6-channel PWM output, 8-channel 14-bit A / D con</p><p>

10、;　　2. Power circuit</p><p>　　Drive circuit from the diode rectifier bridge, filter capacitor and the IGBT inverter constituted; drive circuit using IR's I82130 dedicated MOs power device gate drive dedic

11、ated chip, the chip can not only achieve the optimal IGBT driver, and has a perfect protection, can significantly improve system integration and reliability; isolated part of the use of high-speed optocoupler HCPL4504, i

12、solation from the role of potential.</p><p>　　3. Rotor position and current detection circuit</p><p>　　Due to current high-speed motor, back-EMF waveform distortion is more serious, it is not su

13、itable for position sensorless control for easy installation, the use of small size, convenient installation and electromagnetic Hall sensor mounted on the end of stator windings, the output signal by the partial pressur

14、e , filter the buffer.</p><p>　　PI current regulator current aim is to achieve fast and accurate tracking of a given value, the incremental selection of PI regulator; speed PI regulator related to the system

15、 dynamic and static performance, it is separated from the use of integral PI regulator. Encountered in software design PI regulator design that is the proportion coefficient and integral coefficient kP selection of ki. S

16、ystem uses a factor of AD and Industrial standard procedures set forth in PI coefficient (Kp = 25, Wpi = </p><p>　　And the corresponding current signal directly to the sensor signal input voltage DSP A / D p

17、ort for digital-to-analog conversion.</p><p>　　4. Protection Circuit</p><p>　　Under-voltage protection circuit by detecting the battery voltage, when the battery voltage down to the closure of m

18、otor threshold, the battery does not over-discharge to cause unnecessary damage, to protect the battery. AID voltage power conversion, if the under-voltage, under-voltage when the second location of a sign so that it can

19、 interrupt timer 0 to start from time to time, under-voltage shutdown over after five seconds, jump to self-test mode.</p><p>　　MOSFET over-current protection circuit can protect the most current control wil

20、l set the framework, illustrates the value reached when the motor shut down to avoid a high current through the MOSFET on the risk of burning. Over-current protection is the controller of the last line of defense, over-c

21、urrent protection resistor is used in wire and Culture, current when the system exceeds the maximum protection of current value, the wire will be blown, Culture and Sport in order to play a protective </p><p&g

22、t;　　Drive motor in the process of running the system on the motor will "speed - the current" relevant control, the controller to determine the electrical current and electric vehicles is in the relevant range o

23、f speed, if in the relevant context, the controller should not exceed current limiting settings based on speed control of electric vehicles; when the motor current and speed of electric vehicles is not related to serious

24、, even if the electric current does not meet current limiter settings, if </p><p>　　Further reduce the power flow controller. A negative correlation for each controller to determine the electrical current to

25、 reduce by half until</p><p>　　(B) software strategy</p><p>　　The system software by the main program and interrupt service routine pose. Main program to initialize the main complete system, inc

26、luding the register, variable initialization and the initialization of the external devices, as well as detection of I / O port status. Interrupt service routine are mainly synchronous PWM interrupt service routine, each

27、 current sampling A / D conversion after the end of interruption. Software processes as shown in Figure 2. Optimization of the selection coefficient</p><p>　　Fourth, the conclusions</p><p>　　Hig

28、h-performance brushless DC motor with high-speed real-time digital control system for speed control devices consisting of devices, hardware and software, and control the whole system is relatively simple, low cost, speed

29、 of a smooth, low noise. Experiments show that the control system has good control performance, has good practical value.</p><p>　　永磁無刷直流電機體積小、重量輕，它既具有類似普通直流電動機的良好調速性能，又不存在機械換向裝置，電磁噪聲與干擾小，維護要求低，可靠性好；而且由于不需電勵

30、磁，效率相對較高，因此得到了迅速的發展。介紹一種基于ADI公司ADSP-21992芯片的高速無刷直流電機的控制系統，該系統具有高速、大轉動慣量負載，電機有較大起動轉矩等特點。 基于DSP的電機控制系統具有傳統的單片機電機控制系統和專用芯片電機控制系統的優勢，即專用的電機控制機制、用戶可編程、擴展能力強、功能強大等；同時又克服了它們各自的缺點，如外設和存儲器集成在芯片內，可減少電路板面積、減少系統中元器件個數、提高CPU處理能力、

31、提高系統的可靠性等。系統最終的目標是應用于飛輪系統中的高速無刷直流電機，因此，對處理器的速度要求極高，從實時性能方面考慮，需要選取處理速度盡可能高的芯片。而ADI的2199x系列速度達到了160 M,再考慮到其適應惡劣工作環境的能力，在本文中，我們選擇了ADSP-21992作為核心控制芯片。 （一）硬件構成 1．控制電路 控制電路主要由ADSP21992及其相應的外圍擴展電路構成</p><

32、p>　　欠壓保護電路通過檢測電池電壓，當電池電壓降到閡值時關閉電機，使電池不至因過度放電造成不必要的損壞，保護電池。對電源電壓進行AID轉換之后，如果欠壓，當次欠壓標志位置一，使能定時器0中斷，開始定時，欠壓滿5秒之后停機，跳到自檢工作模式。</p><p>　　過流保護電路可以對MOSFET進行保護，將最大電流控制在設定范圍內，當達到闡值時關閉電機，避免了MOSFET上通過大電流燒毀的危險。過流保護是控制

33、器的最后防線，過流保護電阻用的是康銅絲，當系統電流超過最大保護電流值時，康銅絲會燒斷，從而起到保護作用。</p><p>　　在驅動電機運行的過程中，系統還會對電機進行“速度—電流”相關控制，控制器判斷電機電流與電動車車速是否在相關范圍內，如果在相關范圍內，控制器以不超過限流設定值為依據控制電動車車速;當電機電流與電動車車速嚴重不相關時，即使電機電流沒有達到限流設定值，如果電機電流大于8A，控制器首先減流到8A供

34、電，然后再次判斷車速與電機電流的相關性，在相關范圍內，進入正常供電模式;如果沒有相關性，控制器進一步減流供電。控制器每否定一次相關判斷，電機電流減小一半，直到控制器停止對電機的供電</p><p>　?。ǘ┸浖呗?本系統軟件由主程序和中斷服務程序構成。主程序主要完成系統的初始化，包括各寄存器、變量的初始化以及外部器件的初始化以及檢測I/O口狀態。中斷服務程序主要有PWM同步中斷服務程序，每次電流采樣A